![]() Sturdy Micalex construction, for 3/4" hole. INCLUDES INTEGRALġ2AX7, 12AU7, 12AT7, etc. STYLE MICALEX TUBE SOCKET FOR MINIATURE 9-PIN TUBES. Unlike some phenolic tube sockets on the market, this one fits the 1" hole foundĬERAMIC 8-PIN WIRED OUTPUT TUBE OR RECTIFIER TUBE SOCKET ,Ĭrimped bracket, bottom mount 1 1/4", top mount 1" to 1 1/8", 1 1/2" mountingĬenters, 1" to 1 1/4" chassis hole. Top mounting (mounted from the outside of the chassis), mounting holes spaced 1 1/2" apart. Fits 6L6, E元4, 6V6 output tubes, and 5U4, 5Y3, and GZ34 rectifier tubes. EXACT REPLACEMENT FOR VINTAGE FENDER, VINTAGE Marshall™ (including the JCM900 Series), and many others. TUBE SOCKET, OCTAL 8-PIN, commonly used with the OTB-100 Octal Tube Base to buildīias probes, tube socket savers, tube extenders, etc. 8-pin plug with room inside the baseįor circuitry and wiring. Octal tube bases are used to construct tube socket savers, solid-state Silicone sealant (RTV) which is acryllic-based orīutyl-based is fine. Note: When using an adhesive to secure the keyway to the tube base, DO NOT use a These great tube-savers are sold in sets of 2. In place), your tube can safely be reinstalled into your equipment. This keyway replacement (a little dab of silicone sealant works great to hold it The remainder of the broken keyway from the tube base and properly installing Tube or rectifier with a broken keyway, here is a great solution. Perfect for Twin Reverb, Showman and Dual Showman, Quad Reverb, Bassman 100, Contains four phenolic 8-pin sockets, four "bear trap" retainers,Įight mounting screws, four 470 ohm screen grid resistors (Metal-Film Flameproofįor safety), and four carbon composition 1500 ohm control grid resistors. Perfect for Vibrolux Reverb, Vibroverb, Super Reverb, Deluxe Reverb, Pro Reverb,īassman, Bandmaster Reverb, Tremolux, etc.įrom the original blackface and silverface eras which have four power tubes Princeton and Princeton Reverb do not need the resistors. Safety), and two carbon composition 1500 ohm control grid resistors. Mounting screws, two 470 ohm screen grid resistors (Metal-Film Flameproof for Contains two phenolic 8-pin sockets, two "bear trap" retainers, four For vintage Fender™ amps (NOT Reissues!)įrom the original blackface and silverface eras which have two power tubes (6L6 Fender part number 099072500.įender™ Vintage Amp (60 ` s Blackface and 70 ` s Silverface) Power Tube Socket TUBE RETAINER WITH GRIP TEETH, DESIGNED FOR OCTAL TUBES WITH PHENOLIC BASE SUCH AS 6L6 OR E元4. Theseĭampers are NOT for 9-pin power tubes, such as the EL84 or 6BQ5. Note: Tube shields will not fit over the damper rings, and must be removed from the tubes. Set of 6 rings - will equip either 2 or 3 tubes, depending on the number of rings you choose for each tube. Will withstand high temperatures of pre-amp tubes, reusable when you change An economical alternative to more expensive tube dampers. Use two (or three) of these rings around a pre-amp tube to reduce noise and Shield and base only - socket not included. This is a great kit to replaced all 6 of the tube shields in many Fender™ amps TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL, Replacement for Fender™ and many other brands. Fits 12AX7A and similarly sized preamp tubes. Spring in top of shield which fits over the TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL. ![]() WITH 9-PIN TUBE SOCKET AND INTEGRAL TUBE SHIELD BASE. In 1970 a grounded AC plug and three-position ground switch were added to the rear panel.TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL The aluminum trim was deleted from cabinets when the AA1069 model appeared in 1970. Model: Oxford 12T6, Utah 12” (ceramic) and JBL D-120(For more info, check out the Jensen Replacement Speakers)Ĭomments: AA568 included a major change to the bias section of the power amp which was poorly received so Fender changed the model design to the AA1069 but kept much of the disliked circuitry.Logo: Grille mounted, raised, chrome & black script, with tail, (76) changed to the script, no tail logo. Grill Cloth: Blue White Silver w/ aluminum frame (68-69), w/o aluminum frame (70-80).Feet: Casters on the 2×12 extension cabinet.Hardware: Chrome Corners with lip, Large Chassis Straps 5 5/8″, Side Bar Clips.Speaker Jack, Vibrato Jack, Reverb Jack, Reverb Out, Reverb In Rear: AC Outlet, Ground Sw, Fuse (2A), Power Sw, Standby Sw, Speaker Jack, Ex.Front: Normal: In, In, Bright Sw, Vol, Treb, Bass – Vibrato: In, In, Bright Sw, Vol, Treb, Mid, Bass, Speed, Intensity, Reverb – Master Vol (76-80) – Pilot Lamp.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |